CTC Union FMUX04 Bedienungsanleitung

USER MANUAL FMUX-01 Fiber Optical Multiplexer Standalone / Rack Type 4, 8, 12 or 16 Channel G.703 E1, T1(DS1) Datacom V.35, X.21, RS-530, RS-449,

Chapter 1. Introduction 1-4 Multiplexer Unit : Apr 2003 1.3 Technical Specifications E1 Link Framing Unframed (transparent) Bit Rate 2.048 Mbps

Chapter 1. Introduction 1-5 Multiplexer Unit : Apr 2003 Data Port Channels Interface Types V.35 X.21 RS-530/V.36 RS-449 RS-232 Interface Connectors

Chapter 1. Introduction 1-6 Multiplexer Unit : Apr 2003 LED Indicators Power 1 Green Power Module 1 active Power 2 Green Power Module 2 active Op

Chapter 1. Introduction 1-7 Multiplexer Unit : Apr 2003 Optical Specifications (redundant fiber has identical specifications as primary) Standard

Chapter 1. Introduction 1-8 Multiplexer Unit : Apr 2003 1.4 E1 Signal Structure E1 link line rate The E1 line operates at a nominal rate of 2.048M

Chapter 1. Introduction 1-9 Multiplexer Unit : Apr 2003 The 4-CHANNEL T1 Port Card supports two T1 line codes: AMI coding. B8ZS coding. The 4-CH

Chapter 1. Introduction 1-10 Multiplexer Unit : Apr 2003 This page left blank intentionally.

Chapter 2. Port Card Overview 2-1 FMUX-01Mar 2003 2.1 Introduction This chapter provides brief descriptive over-view of the available 4-Channel Port

Chapter 2. Port Card Overview 2-2 FMUX-01Mar 2003 Ext Clk 1. Rx - (RRing) 2. Rx + (RTip) Figure 2-1. External Clock Connector 2.6 4 x Data

Chapter 2. Port Card Overview 2-3 FMUX-01Mar 2003 When the MULTIPLEXER UNIT is ordered with an V35 Port Card option, a 4-CHANNEL V.35 Card and ada

Chapter 2. Port Card Overview 2-4 FMUX-01Mar 2003 When the MULTIPLEXER UNIT is ordered with an RS449 Port Card option, a 4-CHANNEL RS-449 Card and a

Chapter 2. Port Card Overview 2-5 FMUX-01Mar 2003 When the MULTIPLEXER UNIT is ordered with an RS530 Port Card option, a 4-CHANNEL RS-530 Card and a

Chapter 2. Port Card Overview 2-6 FMUX-01Mar 2003 When the MULTIPLEXER UNIT is ordered with an RS232 Port Card option, a 4-CHANNEL RS-232 Card and a

Chapter 2. Port Card Overview 2-7 FMUX-01Mar 2003 2.7 Ethernet Bridge Module Overview When the MULTIPLEXER UNIT is ordered with an ET100 Port Car

Chapter 2. Port Card Overview 2-8 FMUX-01Mar 2003 Duplex: The original specifications for Ethernet did not allow any bi-directional transmissions.

Chapter 3. Installation 3-1 FMUX-01Mar 2003 3.1 General This chapter explains in detail the requirements and procedures for the installation of the

Chapter 3. Installation 3-2 FMUX-01Mar 2003 3.4 Electrical Installation 3-4-1. Power connection For a model with AC power supply, AC power (90~250VA

Chapter 3. Installation 3-3 FMUX-01Mar 2003 3-4-2. Rear and Front panel connectors All 4-Channel Port Cards install into the rear of the MULTIPLEXER

Chapter 3. Installation 3-4 FMUX-01Mar 2003 3.5 Removal/Replacement Procedures 3-5-1. Optical Module Removal / Replacement ****CAUTION**** All remo

Chapter 3. Installation 3-5 FMUX-01Mar 2003 3-5-2 Channel Port I/F Module Removal / Replacement All 4-Channel Port Cards install into the rear of th

The information contained in this document is subject to change without prior notice. TRADEMARKS Microsoft is a registered trademark of Microsof

Chapter 3. Installation 3-6 FMUX-01Mar 2003 3-5-3 Top cover Removal / Replacement for internal access Normally, there is no need to remove the cove

Chapter 3. Installation 3-7 FMUX-01Mar 2003 3-5-4 External Clock Feature Removal / Replacement ***CAUTION*** This procedure should only be performe

Chapter 3. Installation 3-8 FMUX-01Mar 2003 3-5-5 SNMP Feature Removal / Replacement ***CAUTION*** This procedure should only be performed by quali

Chapter 4. Operation 4-1 Version 1.0b Mar 2003 4.1 Introduction This chapter will go into the details of the specific configuration and operation o

Set the working modes of Optical 1, Optical 2 (if installed), Automatic Laser Shutoff or Loopback function.Chapter 4. Operation 4-2 Version 1.0b Mar

Chapter 4. Operation 4-3 Version 1.0b Mar 2003 The following is a breakdown of the menu system for the Multiplexer Unit (LCD). Power on self test

Chapter 4. Operation 4-4 Version 1.0b Mar 2003 4.3 Terminal Mode Operation The MULTIPLEXER UNIT Control Port (labeled RS-232 CONSOLE on the front p

Chapter 4. Operation 4-5 Version 1.0b Mar 2003 ******************************************** ****

Chapter 4. Operation 4-6 Version 1.0b Mar 2003 Press "1" to enter the System Configuration menu. LOCAL <<< System Para

Chapter 4. Operation 4-7 Version 1.0b Mar 2003 LOCAL <<< Define Optical >>> 1. Optical 1 [ Work ] 2. Opti

CTC Union Technologies Co., Ltd. Far Eastern Edison Science and Technology Center 6F-3, No. 15, Lane 360 NeiHu Rd., Section 1 NeiHu, Taipei, 114 T

Chapter 4. Operation 4-8 Version 1.0b Mar 2003 To modify the Loopback status press "3" LOCAL <<< Define Port 1 Para

Chapter 4. Operation 4-9 Version 1.0b Mar 2003 LOCAL <<< Define Port 2 Parameter >>> Ch A Ch B

Chapter 4. Operation 4-10 Version 1.0b Mar 2003 If we <ESC> back to the "Define System" menu we can configure the card in Port 3 by

Chapter 4. Operation 4-11 Version 1.0b Mar 2003 [ Loopback ] 1. OFF 2. LLB (Local Loopback) 3. NELLB (Near End Local Loopback) 4. RLB (Remo

Chapter 4. Operation 4-12 Version 1.0b Mar 2003 For example to modify the Code Violation threshold, press "1". LOCAL <<&

If we escape out to the root menu, we can select item #1 to display the FMUX status. The display will look like that on the following page.Chapter 4.

Chapter 4. Operation 4-14 Version 1.0b Mar 2003 The Alarm Buffer can be cleared by pressing the "c" key. Note that each entry in the buffe

Chapter 5. Loop Back Testing 5-1 FMUX-01Mar 2003 5.1 General In this chapter we shall explain the functioning of the loop back modes available in t

Chapter 5. Loop Back Testing 5-2 FMUX-01Mar 2003 E1/T1 4-Channel Port Card Loop Back * LLB (T1/E1 local loop back) near end (NE)

Chapter 6. SNMP Operation 6-1 FMUX-01Mar 2003 6.1 General The Simple Network Management Protocol (SNMP) is one of many protocols in the Internet Pr

Table of Contents i Chapter 1. Introduction …………………………………………... 1-1 1.1 General …………………………………………………….. 1-1 1.2 Functional Description …………………………………

Chapter 6. SNMP Operation 6-2 FMUX-01Mar 2003 6.3 The Management Information Base The management information base (MIB) includes a collection of man

Chapter 6. SNMP Operation 6-3 FMUX-01Mar 2003 Under this scheme, the path to CTC Union's Enterprise branch would be: iso(1).org(3).dod(6).inter

Chapter 6. SNMP Operation 6-4 FMUX-01Mar 2003 Connect a terminal to console port as usual. Login to the local unit. *********************

Chapter 6. SNMP Operation 6-5 FMUX-01Mar 2003 Press "9" to enter the SNMP Card Configuration menu. LOCAL <<< SNMP Card

Chapter 6. SNMP Operation 6-6 FMUX-01Mar 2003 LOCAL <<< Manager Config >>> 1. Access IP #1 [ 0. 0. 0. 0] [comm

notes: A-7

notes: A-8

Technical Inquiry Form MODEL No.: FMUX01 Please fill in the co nfiguration settings with ' ?' marks into the following table. Send it to

Table of Contents ii Chapter 4. Operation ………………………………………..…... 4-1 4.1 Introduction …………………………………………...…... 4-1 4.2 LCD Menu Operation …………………………

E1/T1 DSU/CSU Series Fiber Converter Series CTC Union Technologies Co., Ltd. Far Eas

Chapter 1. Introduction 1-1 Multiplexer Unit : Apr 2003 1.1 General Thank you for choosing the Fiber Multiplexer. If you would like to skip right t

Chapter 1. Introduction 1-2 Multiplexer Unit : Apr 2003 The 4-CHANNEL T1 Port Card provides four RJ-45 (100 Ohm balanced) connectors for T1(DS1) Lin

Chapter 1. Introduction 1-3 Multiplexer Unit : Apr 2003 PPPWWWRRR---222 PPPOOOWWWEEERRR PPPWWWRRR---111 PPPOOOWWWEEERRR PPPooorrrttt 111 CC